[Loud3]

do i have to look out for center bore size (67.1mm)
i'm planing to buy Japan Racing JR11 rims and don't see CB size anywhere on their size

Most 5x114.3 bolt patterns will come with a larger standard centerbore to allow for hub centric adaptors to fit a wide variety of makes and models.

 

[CREG_38]

Finally got my Wheels and tires installed.
18x8 Et 45 Konig Oversteer in Opal
245/40/18 Yokohama Advan Sport A/S

 

[pocafred]

mazda6 wheels r17 215\55

 

[apme123]

Gen1 Mazdaspeed wheels on Corksport lowering springs.

 

[Somthinglocal]

So guys, just found a set of wheels for the car, but i'm not sure they will fit.
This i for agressive fit only maby some camber.

The wheels are 20x9 +20 in the front 20x10.5 +25 in the back, and i don't think they will fit :-/
But need some expert help please, so i can get on with my life :laugh2:

 

[Dova]

Don't get why people are trying to run staggered wheels on a FWD car.

 

[Somthinglocal]

Don't get why people are trying to run staggered wheels on a FWD car.

Well thats up the person who own the car :laugh2:

 

[ELegend3]

So guys, just found a set of wheels for the car, but i'm not sure they will fit.
This i for agressive fit only maby some camber.

The wheels are 20x9 +20 in the front 20x10.5 +25 in the back, and i don't think they will fit :-/
But need some expert help please, so i can get on with my life :laugh2:

20 inch on the Mazda 3 is a no no in my opinion. It's too large and heavy. Plus, yes, you would need a lot of negative camber. I highly recommend looking for different wheels:/

 

[Somthinglocal]

20 inch on the Mazda 3 is a no no in my opinion. It's too large and heavy. Plus, yes, you would need a lot of negative camber. I highly recommend looking for different wheels:/

Dam it, a friend of mine have a set of vossen CVT i could get for 500$, but i wont buy them if they don't fit :-(

Bu thanks ELegende3

 

[The Dark Knight]

20 inch on the Mazda 3 is a no no in my opinion. It's too large and heavy. Plus, yes, you would need a lot of negative camber. I highly recommend looking for different wheels:/

Agreed, plus everyone I have seen makes the stock rotors looks so small that there is a serious tradeoff on visual improvement.

 

[loong]

Test fit of some 18x8.5 et46 Work Emotion XT7's. They currently have 225/40/18's on them but after the test fit and a quick roll around, I'm sure you could fit up to 245/40/18 easily as there's plenty of room. The car is also lowered on Eibach springs.

 

[S3BAZ1091]

OEM Mazda RAYS 18x7 ET 50, looking into getting some Corksport Lowering Springs and also some spacers, but don't know what size spacers ill need for a flush/clean look. I will eventually get coils towards the end of the year.

 

[mazdaspeedmyk]

@S3BAZ1091, the Mazdaspeed center caps are a really nice touch. Were those OEM?

 

[S3BAZ1091]

@S3BAZ1091, the Mazdaspeed center caps are a really nice touch. Were those OEM?

Yes sir - Mazdaspeed Center Cap for use with RAYS Wheels QWWS-37-19C -02 $43.95

 

[YQGmazda3]

19x8.5 40offset Morr Wheels Tripple Matte Bronze -- Toyo T1Proxes 235 35 19

That was the exact look I was going for. What springs did you use to lower the car? How much did it lower?

 

[The Dark Knight]

Best looking set up I have seen on this thread yet. This is what I was looking for. Will be going for the same look on my 16 GT Deep Crystal Blue hatch. Very clean, very dope

Which one are you referring to?

 

[JM85]

Which one are you referring to?

Minsanity's ride

 

[JM85]

Do you guys think I can get away with an 18x7.5 inch Enkei Nt03 with a +38 offset lowered on Eibach Pro Kit springs? From everything I have read on this thread a wheel that skinny could get away with that offset without any issues.

 

[Rx7rocket2010]

Just ordered my rotiform blq's 19x8.5 with 225/40/19 pilot sports

 

[tccurtis]

CX-7 rims.