specs

I found some wheels I like and was wondering if these specs would work. I have a 2014 i sport with 16in wheels. Here are the specs: Size: 18 x 8 Bolt Pattern: 5x114.3 Offset: 40 Hub: 72.60 Thanks.

I've decided that i want to take the route of a thicker profile for a meatier look than a thin profile. I was wondering if anyone has advice or knows this setup/specs? This is not my picture but i came across it searching through forums. I have the same car and love for it to sit like that.

Hi all, I'm new to this forum and was doing some work on my Mazda. Does anyone know of a good site for getting the torque specs of a 2008 Mazda 3 2.0L?

Planning to replace the 2nd cat before the resonator with a vibrant resonator. (2015 S GT) Does anyone know the internal diameter and length of the stock cat? I was thinking 2.5" internal w/ 18" or 12" length but wanted to be sure.

Anyone know the diameter and thread pitch on the nuts used with these? I’m looking into mil-spec distorted thread locking nuts to replace them with. Tired of these coming loose and clunking/popping on the slightest suspension compression on either side.

Hey everyone, Has anyone ran into little specs of rust spots on the back of there rear hatch on a cx5 its white so i can notice it when washing it etc, only seems to be on the rear hatch

Hello everyone! Question pls. I just got my car back after it was in an accident and had multiple suspension components changed. My Question is this.... On a 2014 Mazda 3 GT 2.5L should there be Negative Camber on both Front Driver and Passager wheels? I had the alignment re-done today...

Does anyone know what the OEM alignment specs are for a 2011 5door 2.5L? Just upgraded from 17x7 rims to 18x8 rims on 225/40/18. Will be getting rear adjustable camber arms soon. TIA

I'm after the dimensions for the sure weighted gear knob but any other will do if anybody can help me out. If your in Europe and can get me the specs I'll happily make you one and mail it.

I'd like to know some details about the system in my car eg true wattage, frequency response etc. Also what are the options for upgrading such as adding a sub?

Hey all, I've been trying to decide on some new wheels for my 2014 mazda 3 hatchback for a while now but I'm just unsure of what size and offset to go with. I've narrowed it down to 3 choices but I need some help as far as fitment wise. It's between a 17x9 +30, a 17x9 +35, or a 18x8.5 +30. Any...

Have been searching the forum for dynos of the stock Mz3 2.0L (US spec, but others are ok, too), but have only been able to find one so far (see link below). http://www.knfilters.com/dynocharts/69-6033_dyno.pdf I'm assuming that folks who have made intake/exhaust mods have posted more, but...

I'm thinking I'll have to get a set of winter wheels and tires for my '15 S-GT and will go with 205/60-16s on alloy wheels. On the previous car I used steel wheels, but dealing with the added weight and especially the wheel covers got to be a huge PITA. Anyway, looking at what's available, I'm...

I was worried about my alignment because after I lowered my 2005 3, I never got an alignment and stupidly replaced my tires every 10k miles. I've had my Corksport springs installed for about 3k miles and they feel settled, lower, and a little bit rougher. I went to a place called Express Tire...

This topic might belong in the Engine forum but I will post here. I am wondering if the engine specs on the Japan engine and US engine are the same. Here in Asia we can run on E85, not sure if US spec cars can. And I was just reading a Mazda Asia ad and it said, "Skyactiv-G 2.0 engine power...

How much should I torque my Mazda 3S GT 18" wheels? I watched a mechanic at my dealership torque my lug nuts with a torque wrench today and I asked him how much torque he used. He said 102 ft-lbs(!). That seems pretty high to me. Is 102 the correct torque spec for our 2014/2015 Mazda 3 18"...

im looking to get some black rims for my mazda3 4 door s gt. Im currently looking at Enkei Wheels - Performance Wheels - EKM3 and the OEM 18 alloy in gunmetal, i think i will go with the ekm3 since it is less expensive. Im not sure which spec of rim i should get and bolt pattern? i want the same...

Good day everyone. Time to take the car and get it aligned after I put on the new tires. I did several searches for the alignment specs and did not find much. Does anyone have them handy that they can share? I do recall reading about doing zero toe front and back for much better wear. Is...

I noticed some people complaining about the road noise on the Mazda3 so I dug around to find some specs on it: Ford Focus Mazda 3 Idle 43 dBA 37 dBA Full Throttle 79 dBA 77 dBA 70-MPH Cruise 73 dBA 70 dBA The Mazda3 is clearly the quieter car compared to the...

Anybody have custom alignment specs to share? I'm taking my 3 in for alignment and would like something more performance oriented, my friend suggested -1.5 camber up front and -1.0 camber in the rear? Not sure if this good or not...this alignment should utilize the stock suspension. I want...