installed

So I had the accessories installed recently that aren't in stock at time of purchase, this included the home link auto dimming mirror and they updated the firmware at the same time. The next day I tried to use the heater (after 15 minutes of driving) and the air wasn't warming at all regardless...

Koni SA's, H&R's, Progress RSB soft setting done earlier today. The GRP end link threads stripped and my shop said the metal was soft. They had to install the OEM end links back on so I could get home. The rear GRP's went on fine, the fronts stripped. I would appreciate some other...

Hey so I purchased an Injen cold air intake (tuned intake) for my 2014 Mazda 3 2.0 ... installed it no problem, very easy obviously. About a week later the check engine light comes on throwing code P0171 .. so I loosen all clamps and re-position pipes and re-tighten everything.. light goes...

I'm new to this forum, so sorry if I placed this in the wrong thread. I have a Mazda 3 2012, and installed some aftermarket LEDs today. I took out the factory low and high beams without much trouble. However, when I was installing the aftermarket ones that I bought, I noticed I did not hear a...

I just installed Apple Carplay today. Carplay works just fine but now the airbag light on my dashboard blinks. I am assuming I inadvertently did something to an airbag sensor, but do not recall. Does anyone have any ideas what it could be? Incidentally, I did not disconnect the negative battery...

OK, i bit the bullet and installed Tribotex into my oil crankcase this evening. Got $20 off, so paid $79.20, including free shipping direct from the company website 15,663 miles on my '17 2.5 gt hatch (bought Feb 2017). Tells you that you must allow at least 500 miles of normal driving to...

I recently picked up a 2012 Mazda3 Sedan Skyactiv after a buddy of mine wrecked my 2010 Mazda3 Sedan. I would like to start adding in come tasteful subtle mods, so far interior leds are on. I would like to see how the sedan would look with that spoiler on and decide if its a hit or miss.

Hi all- I hate looking at my phone while in the car, and I can't stand cables, so I wanted a way to get everything out of sight. I installed a wireless phone charger in the center console of my 2015 3 hatch. I'll post a photo later if I get time. Here are the products I used: 1. Two port...

Hey guys this is my first post here but I have searched extensively on the matter to find an answer but would like to make a post. I have just installed a xb35 TRS kit in my 2017 mz3 and have read about the projectors being prone to burns from the uv light created by hid kits. I used to own a...

I decided to pull the trigger on some LED low beams from amazon.ca and gotta say i am quite happy. they were only 50$ so i wasnt expecting the most from them. I only bought low beams in case they werent great. i do intend to buy the hi beams and fogs now because they look good. Here is a video...

I've seen these on eBay and they looks very nice especially since the turn signals are now LED. I'm reluctant to get these because I've seen zero install videos or guides, and was wondering if someone here has them and has installed them successfully. If so could you guys comment on how reliable...

Does anybody know where the interior lighting package footwell lights are located? Does anybody know what they look like? All my interior led lights work, except the ones lighting the footwell. Sent from my iPad using Tapatalk

Overall the process wasn't too bad. This was my first time installing a car stereo but from what I've seen pioneers/alpines should be similar. I tried adding links to the guides that helped me but I'm under the post limit. Parts you need Double din radio Metra 70-7903 Harness iDatalink RR...

Yup, got rid of that wimpy horn and installed the Hella Supertone Twin Horn Kit using fizyliftingdrnks install guide in the DIY/How to thread. http://mazda3revolution.com/forums/2010-13-mazdaspeed-3-how-guides/55002-2010-mazdaspeed-3-hella-horn-install-guide.html Took a couple of hours, only...

Big thanks to @louis110 for his instructions, albeit for corksport different springs, same concept, only with racing beats you use all the stock hardware, just the springs are swapped. Link to Louis110's guide...

Wow. That's all I gotta say... I bought these things on a whim because I know they're a rare part -- bought them back in March I think it was knowing they were going into pre-order for a manufacturing run. Well they finally came yesterday. Installed them inside of 10 minutes and turned them on...

I've been eyeing installing AVS wind guards and I don't know if I should go with in-channel or taped-on. What do you think?

Hello Mazda Proud owner, My name is Jatin... Very new here. I own a 2016 CX5 and 2014 Mazda 3. Yesterday, I installed latest new firmware NA 5900 441.. on my CX5 ...later i ended up installing some tweaks of the AIO program tweak installer as per instructions, they all worked like charm without...

...And I thought I would post a pic. This setup definitely took the sharpness out of the crap CA roads I have to drive on. I haven't gotten it mad on corners yet, but it seems to keep more level on the various off/on ramps I have to use. My 2012 3s 6-Speed has the following: - Koni FSD's...

Hello everybody I have Mazda 3 model 2016 with mzd connect 59.00.330 4A N i tried many tweaks all is worked but only video player doesn't worked i tried the video player 2.7 and 2.8 wish included in mazda aio 2.5 installed successfully but is not visible in application section. anyone can...