2004 to 2020 Mazda 3 Forum and Mazdaspeed 3 Forums banner
cupholder
1-11 of 11 Results
  1. Mazda 3 Parts - Buy / Sell
    Greetings! This is for 2019 owners in the NYC/Long Island Area. I'd like to have the front center console cupholder with lid which only came with the 2019 model. (2020 and after has an open cupholder.) Surface scratches on the gloss black are a non-issue since I will be wrapping it...
  2. 2014-2018 Mazda 3 Skyactiv Appearance & Interior
    Just showing off some trial-and-error mods I did with my cupholders. Most mornings I have a 16-oz stainless steel coffee mug, tall with a half-hourglass or inverted-coke-bottle shape. (Sorry no pic of it.) Because the bottom is narrower than the top, it tends to tip over, though it hasn't done...
  3. Diode Dynamics
    Went ahead and checked out this sponsor after not seeing much about them/by them. I ended up ordering a cup holder insert for my car, and my friends Subaru LGT (without any pictures of what the product even looks like!). I figured I would post up a picture of what it looks like. I went with the...
  4. 2010-2013 Mazda 3 & Skyactiv Appearance & Interior
    I'm planning on doing some easy mods before the end of summer and stumbled on this: 2010-2012 Mazda 3 LED Cupholder Accent - 3 - Mazda - Acrylic No reviews, no customer pics, searched the webz - nada. From the one picture they have of it, it looks real nice and professional; I think it'd be...
  5. 2010-2013 Mazda 3 & Skyactiv Appearance & Interior
    Just my version of LED Cup, I used RBG LEDs rather than a static color. I used RGB LED bars, and a 12v controller that has 8 static colors, and 8 transition modes. These were installed just as many others were. 1. Run power from accessory line into RGB controller 2. Mounted RGB Controller...
  6. 2010-2013 Mazda 3 & Skyactiv Appearance & Interior
    Here's my version of an old favorite!:punk: Pull out the cupholder, install some LED panels or lights of your choice along the drivers side edge, wire them to the front power port...... ....add bottled water for cool pics! Hey check it out, we're pre-wired for heated seats! That's the front...
  7. 2010-2013 Mazda 3 & Skyactiv Discussion
    There's really no easy way to say this, if something absolutely stupid can happen to me, it will. I had a lighter in my cupholder, somehow it slipped partway into the crack between the bottom of where the lid opens and the bottom of the cupholder. I tried to get it out, and well, you can guess...
  8. 2010-2013 Mazda 3 & Skyactiv Discussion
    Hi all, My girlfriend placed her ring in the cupholder compartment between the seats and the ring slid back and fell through the gap/hole that's located in the back of that cupholder setup...if you place you finger back there you will feel it and it drops down to underneath the center console...
  9. 2010-13 Mazdaspeed 3 How-To Guides
    I couldn't find any specific guides with pictures for disassembling the 2010 MS3 center console (it is a tad different from gen1) for installing the TWM Shifter Bushings. Luckily it wasn't that hard, but for someone who's never really modded a car before, even pulling apart plastic housing can...
  10. 2010-2013 Mazda 3 & Skyactiv How-To Guides
    So, as I stated awhile ago, I saw how BeEvil wired some LEDs into his cupholder, and I thought I would post up a DIY to put these in. super easy install. Any of you can do this with basic wiring knowledge and a little patience. Good luck! Special Thanks to BeEvil and Derrick_B This is my...
  11. 2010-2013 Mazda 3 & Skyactiv Appearance & Interior
    So, i was surfing around on the internet, and I found a post by BeEvil on another site (cheater). He has an LED set-up in his cupholders, and i looks REAL nice! So, we've been PMing back and forth, about where he got 'em, how much, so on and so forth. I've had a terrible time finding some of...
1-11 of 11 Results
Top