Search Results for ‘abs’

Im looking to buy the V2 Front bumper from knight sports which is made of FRP material. To save money on the remaining kit (rear, side skirts, and spoiler) I have found companies here in Toronto, Canada selling replicas which look identical to the real thing but they are made of ABS Plastic. I...

Just wondering if anyone has properly removed the abs system so it doesn't affect any other systems but still gives you full breaking ability. I hate abs and I never want to use or deal with it. It's not so bad on the dry roads but in the snow it's horrible and makes my breaking distances almost...

Hi, anyone with a good solution for fixing ABS/TCS lights coming on in their Mazda3? I have a 2nd gen 2009 Mazda3 with 50,000 miles on the clock. A couple of weeks ago the ABS and TCS lights came on at the same time. After a few days the lights went off, and after another few they came back on...

Hi All - (Hope this is in the right section) I added sound deadening and soundproofing material to my 2.5L hatch following this DIY write-up (Cheaply and effectively sound deadening your 2010-2013 Mazda3) and disconnected the battery prior to disconnecting the airbag connectors under the seats...

i have a issue with my abs where if i press my brakes just hard enough for the abs to kick in, i feel it pulse through the pedal as you should. but if i hit it hard enough for the EBA to kick in, the front left wheel will lock up till the car comes to a stop before letting the brakes go (ie...

What does the diagnostic troubleshooting code (DTC) *C0120* mean on a 2010 Mazda 3? The ABS warning light is also on. Googling it only comes up with a message for a fault on a Toyota but nothing that I can find for a Mazda 3. Thanks, Nick

So I have this strange issue that I have not been able to figure out, to be fair it's on a Mazda 5 but it's not too different from a 3. Anyway, when the ABS is actuated, the brake pedal goes to the floor but will still stop. I turn the car off, then turn it back on a few seconds later, the...

I'm going to flush out my brake lines and clutch at some point, easy job and don't need help there. Where I'm a little stuck is flushing out the abs module? I've never had to do that one....my old car didn't have abs! I know that doing it 'properly' means the dealer needs to hook electronics up...

I'm putting a new transmission in my 2005 Mazda 3s and it has a manual transmission. However I wanted to know the difference between the trans with abs and the trans without abs. My car has abs and I can't find a trans anywhere close with abs only without. I was curious if I could use a trans...

Hi, I recently bought a used Mazda 3 2016 iSport and the TPMS light starts blinking for a few seconds and stays on and ABS light is always on. I went to the dealer and they said I need to replace ABS module but gave the part number as BHP1-57-K30A which comes up as SDM module. I am confused if...

Hey guys. I just purchased a BaysonR spoiler for my '17 hatchback. As some of you may know, BaysonR's products are made of ABS plastic, and they come unpainted. Therefore, I will have to paint the spoiler myself. Unfortunately, I have absolutely no idea how to go about doing this. I don't...

How bad is it if the ABS case has been cracked just enough that there is an opening? Could it be sealed instead of being replaced?

I need to disable my ABS, has anyone done this on a 2014+ Mazda 3 yet? If so which fuses do I pull? Usually its one of the fuses under the hood. I can do trial/error method but am hoping someone else has done this before already and knows which one(s) to pull. Disclaimer, I am not debating...

So my traction control light and ABS sensor lights came on a couple weeks ago. My speed control also stopped working at the same time. I was told that this was because of a faulty ABS sensor, so I go in to remove the passenger side and I find out it's stuck. Well.. worst possible thing happened...

Not sure why, not sure how to fix. Any ideas? Could they have broken a sensor or is there a way to reset the lights? They do not blink. I drive a 2011 Mazda 3

I recently bought an 08 Mazda 3 hatchback for my daughter and she loves it. We are needing yet another car so I'm seriously thinking about getting another Mazda 3 that is a couple of years newer. I found a 2010 with around 100k miles that is in great shape & priced good, the only problem is...

I have a 2014 Mazda3 with about 17k miles. When I first give the car gas after startup, I hear a series of creaks coming from somewhere under the engine bay (I think). Again, it only happens after I put the car in D and apply my foot on the accelerator for the first time. I don't hear any other...

I have a 2010 Mazda 3 GT with 2.5 L engine. ABS and Traction control lights are on. I understand there is a way to read the codes if the lights are blinking, but how do I get the lights to blink? Is my only recourse a trip to a dealer? I found instructions for older Mazdas that involve...

Took me several hours to find these. This is for the air bag system (ABS) on 2nd generation Mazda 3's. Unlesss you have the $1,000 code readers that the Mazda dealerships have, you can't read the codes through the OBDII port. The only way to diagose is to watch the air bag light and how many...

Dear all, I’m the owner of a Mazda 3 I, 2010, 47 000 miles, in Miami FL 8 months ago, I started to have ABS and TSC warning light coming on and off. It could stay on a day or more and then be off for couple of days. The only pattern I noticed: most of the time, the lights were on when it was hot...